Skip to content
DIS Robotics
ROBOTICS · ENGINEERING · ORIGINAL SOURCES
WORLD B-1 · TECHNICAL BRIEF
Technical BriefDeployed4 min read

The gearbox does not create torque for free

RADAR76

A robot joint needs torque, speed and manageable inertia at the same time. The ratio on the gearbox is only the opening bid.

Published
Updated
Primary Domain
Industrial & Manufacturing
Deployment Maturity
Deployed
Sources
3 listed · 3 live links
Reading Time
4 min read
ActuationControl SystemsManipulation

DIS points readers toward original work. Source facts, DIS interpretation, and the editorial verdict are kept distinct below.

What Changed

Source-grounded summary

A reduction ratio is a wonderfully persuasive number. Put a 50:1 gearbox beside a 10:1 gearbox and the larger one appears to have won the strength contest before anybody connects a motor. Unfortunately, the joint still has to move.

This is an engineering explainer, not a new product announcement. It draws on maxon's technical guidance about motor operating points, gearhead inertia and static torque transmission. Those documents describe related constraints that are easily missed when a gearbox is chosen by output torque alone. [1–3]

Why It Matters

DIS interpretation

A robot joint is a coupled system: motor, transmission, load, structure and controller. The transmission changes how that load appears to the motor and how the motor appears to the load. It also spends some of the available mechanical power on losses.

That makes gearbox selection a negotiation between requirements. A slower joint may be perfectly adequate for a valve operation and unusable for a fast pick. A joint that reaches its peak torque briefly may still fail a repeated duty cycle. The useful question is whether the combination meets the motion profile and load envelope, not whether its biggest catalog number looks reassuring.

How It Works

DIS interpretation

Let N be motor speed divided by output speed. For a simple reduction model in motion, output speed is motor speed/N, while output torque is approximately motor torque × N × efficiency. These relations are bookkeeping for an assumed operating point; efficiency and allowable torque must come from a real component's documentation. [1]

  1. Spend speed to buy torque

    Here is an illustrative DIS calculation, not a measurement of a commercial motor. Assume 0.20 N·m at 3,000 rpm. With N = 10 and an assumed efficiency of 0.85, the model gives 1.70 N·m at 300 rpm. With N = 50 and an assumed efficiency of 0.70, it gives 7.00 N·m at 60 rpm.

    The second arrangement delivers more torque and one-fifth the output speed. Its lower assumed efficiency also leaves less mechanical power at the output: approximately 44 W rather than 53 W. Nothing has been multiplied into existence. The gearbox is a currency exchange, and the service fee is paid in losses.

  2. Choose which side is looking at the inertia

    Maxon explains that load inertia referred to the motor decreases with the square of the reduction ratio. An ideal 10:1 reduction makes the load contribution at the motor one hundredth as large. The motor must still accelerate its own rotor and the gearhead's input-referred inertia. [2]

    Looking from the output toward the motor produces the complementary issue: ideal rotor inertia is multiplied by N squared. That can matter when an external contact tries to accelerate or backdrive a joint. These statements refer to different sides of the same transmission; they are not competing descriptions of whether gearing is good.

  3. Check the operating point before the headline rating

    Maxon's motor guidance cautions that power ratings alone are a poor basis for selection: the motor must supply the required torque at the required speed. Continuous torque, permissible speed and the application duty cycle matter. [1]

    For a proposed joint, start with the output motion and load over time. Translate them through the candidate ratio, then check motor and gearhead limits. Include transmission inertia and losses in a suitably detailed model. Finally, test the actual assembly. A spreadsheet has an excellent cooling system because its motor exists only in a cell.

The Mechanical Lens

DIS interpretation · source-supported dimensions only

Signature DIS section — only engineering dimensions available in the underlying material are shown.

Actuation

Reduction trades angular speed for torque subject to losses. Motor current limits, available voltage and the selected operating point remain relevant; a ratio alone is not an actuator specification. [1]

Loads

Distinguish load inertia reflected to the motor from rotor inertia reflected to the output. Include the transmission inertia instead of treating every gear as massless. [2]

Thermal

A brief peak and repeated or continuous operation are different selection problems. Check the actual motor operating envelope and installation conditions. [1]

Environmental constraints

At zero shaft speed, ordinary power efficiency cannot be calculated as output power/input power because both mechanical powers are zero. Static friction still affects transmitted torque. [3]

Deployment

DIS interpretation

  • Applicable to selecting joints for manipulators and industrial motion systems; numerical examples above are hypothetical.
  • A real selection also needs component-specific torque, speed, inertia, mechanical-load and duty-cycle data.

The Catch

DIS interpretation

LIMITATIONS & OPEN QUESTIONS

The arithmetic assumes a fixed operating point and chosen efficiencies. It does not simulate a motor controller, temperature rise, elastic transmission, backlash, friction curve or contact dynamics. The efficiencies are illustrative inputs, not maxon specifications.

Be especially careful at standstill. Maxon's blocked-shaft guidance explains that ordinary power efficiency is undefined there and static friction cannot simply be wished away. [3] Nor does a high ratio alone establish self-locking, reliable backdriving or safe holding after power loss. Those behaviors depend on the mechanism and installation and need their own evidence.

HIT THE QUESTION BLOCK BEFORE YOU BELIEVE THE HYPE.

DIS Verdict

Editorial verdict — not source fact

DIS EDITORIAL JUDGMENT

Choose the ratio after writing down what the joint must do: torque, speed, acceleration, contact behavior and repetition. A larger reduction may be exactly right. It becomes a defensible choice when the motor-side requirements, output-side behavior and component limits agree. “More torque” is the start of that conversation, not the sign-off.

Sources

Original material

Follow the original material to check methods, test conditions, and limitations. Source claims are distinct from DIS interpretation.

  • Technical Docs · maxon / Urs Kafader

    [1] Assigned power rating of DC / EC (BLDC) motors

    Checked 16 November 2026. Motor torque-speed operating point, continuous versus short-term operation and limitations of power-rating comparisons. Manufacturer engineering guidance.

  • Technical Docs · maxon / Urs Kafader

    [2] Gearhead: Mass inertia

    Checked 16 November 2026. Input-referred gearhead and load inertia. DIS derives the complementary ideal output-referred rotor relation explicitly.

  • Technical Docs · maxon / Urs Kafader

    [3] Gearhead efficiency at blocked state

    Checked 16 November 2026. Distinguishes zero-speed mechanical power from static torque transmission; does not certify a particular robot joint.

Primary attribution label: maxon / Urs Kafader